Disposable Coveralls
Limitations of Use
The information provided on KLEENGUARD* Overalls in this website is intended for general guidance only, please refer to instructions for use.
KLEENGUARD* Overalls are not sterile and should not be used in hazardous conditions where exposure to ultra fine particles, corrosive chemicals, toxic substances, poisonous fumes/vapours or radiation is present.
Intensive liquid sprays, biohazards or high temperatures, will require greater protection than that offered by KLEENGUARD* Overalls. In all conditions, alternative suitable protection should be used for the face, hands and feet, together with respiratory equipment where required.
Do not wear KLEENGUARD* Overalls if torn, faulty or damaged in any way
It is the responsibility of the user to ensure that KLEENGUARD* Overalls meet the specific requirements of its intended use and complies with any statutory or regulatory requirements or acceptable standards.
Kimberly-Clark Australia Pty Ltd and its distributors cannot guarantee product performance if garment usage is inconsistent with information on this website and contained in the product brochure and accepts no responsibility for improper use of KLEENGUARD* Overalls and subject to law give no warranties as to the product except as expressly set out above
KLEENGUARD® A40 SIZING CHART
KLEENGUARD® OVERALLS SIZING CHART
Limitations of Use
KLEENGUARD® XP Overalls can not be used with highly toxic or hazardous chemicals, chemical vapours and gases. Exposure to small particulate matter, naked flames, sparks or hot surfaces (the fabric will begin to melt at 120°C) should be avoided.
Disclaimer
KLEENGUARD® XP Overalls are suitable for the intended use and comply with regulatory requirements. Kimberly Clark Australia Pty Limited and its distributors accept no responsibility for improper use of the KLEENGUARD® XP overalls, and subject to law give no warranties as to the product except as expressly set out above.
European Legislation
In 1989 the Personal Protective Regulations (PPE) were introduced to protect the European workforce. The law divided PPE into three categories, according to the level of protection offered.
- CE Simple: Category 1 minimal risk
- CE Intermediate: Category 2
- CE Complex: Category 3 risk of serious / mortal danger
CE Complex
Guidelines have been drawn up within the CE Complex category to help users identify the correct garment for the task. These are called ‘Types’ and are listed below:
- Type 1 – Gas Tight clothing
- Type 2 – Non-Gas tight clothing
- Type 3 – Liquid Tight clothing
- Type 4 – Spray Tight clothing
- Type 5 – Particle Protection
- Type 6 – Limited Splash Protection
Meeting your legal responsibilities
As an employer you’re required by law to complete the following:
- Eliminate risk wherever possible
- Assess the need for protective clothing in your work environment
- Provide garments that protect the user against risk free of charge
- Train the wearer on how and when protective clothing must be worn.
We’re committed to working with you to meet all these criteria.
What you should demand of us
European regulations demand manufacturer’s products:
- Satisfy safety requirements based on the category of protection claimed
- Are subject to Type-examination by an approved body
- Carry a CE mark and information about the products
- Are manufactured under an approved quality system
We meet all of these criteria, as all of our KLEENGUARD® XP Protective overalls carries a CE mark awarded by SGS, an internationally recognised Certification body.
European legislation can be confusing. Our protective clothing pyramid will help demystify legislation by providing an overview of levels of protection according to design and ‘Type’.
In simple terms the lower down the pyramid, the lower the level of protection.
Just use your risk assessment in conjunction with our pyramid to help identify the level of protection you need.
KLEENGUARD* Disposable Overalls are designed to assist in the protection against hazardous dust and particulate matter, whilst also providing a good level of repellency against light sprays of water based liquids. View the data below about the KLEENGUARD* A40 Coveralls Fabric Performance Against Chemicals.
Fabric Name | Chemical | CAS Number | Concentration | Penetration EN 368 | Repellancy EN 368 | Permeation EN 374 / ISO 6529 |
KLEENGUARD* A40 Fabric | Acetic Acid | 64-19-7 | 40% | Class 3 < 1% | Class 3 > 95% | Perm Not Tested |
KLEENGUARD* A40 Fabric | Acetone | 67-64-1 | 100% | Class 3 < 1% | Class 1 > 80% | Perm Not Tested |
KLEENGUARD* A40 Fabric | Acetophenone | 98-86-2 | 100% | Class 3 < 1% | Class 3 > 95% | Perm Not Tested |
KLEENGUARD* A40 Fabric | Buraton 10F | 100% | Class 3 < 1% | Class 1 > 80% | Perm Not Tested | |
KLEENGUARD* A40 Fabric | Ethanol | 64-17-5 | 95% | Class 3 < 1% | Class 2 > 90% | Perm Not Tested |
KLEENGUARD* A40 Fabric | Ethylene glycol | 107-21-1 | 100% | Class 3 < 1% | Class 2 > 90% | Perm Not Tested |
KLEENGUARD* A40 Fabric | Formaldehyde | 50-00-0 | 37% | Class 3 < 1% | Class 3 > 95% | Perm Not Tested |
KLEENGUARD* A40 Fabric | Heptane | 142-82-5 | 100% | Class 3 < 1% | Class 0 | Perm Not Tested |
KLEENGUARD* A40 Fabric | Hydrochloric Acid | 7647-01-0 | 37% | Class 3 < 1% | Class 2 > 90% | Perm Not Tested |
KLEENGUARD* A40 Fabric | Incidin Extra N | 100% | Class 3 < 1% | Class 1 > 80% | Perm Not Tested | |
KLEENGUARD* A40 Fabric | Incidin Plus | 100% | Class 3 < 1% | Class 1 > 80% | Perm Not Tested | |
KLEENGUARD* A40 Fabric | Incidur | 100% | Class 3 < 1% | Class 1 > 80% | Perm Not Tested | |
KLEENGUARD* A40 Fabric | Nitric acid | 7697-37-2 | 40% | Class 3 < 1% | Class 3 > 95% | Perm Not Tested |
KLEENGUARD* A40 Fabric | Quartacid Plus | 100% | Class 3 < 1% | Class 1 > 80% | Perm Not Tested | |
KLEENGUARD* A40 Fabric | Sekusept | 100% | Class 3 < 1% | Class 1 > 80% | Perm Not Tested | |
KLEENGUARD* A40 Fabric | Sodium Hydroxide | 1310-73-2 | 48% | Class 3 < 1% | Class 2 > 90% | Perm Not Tested |
KLEENGUARD* A40 Fabric | Sulphuric Acid | 7664-93-9 | 35% | Class 3 < 1% | Class 3 > 95% | Perm Not Tested |